Services · Machining & fabrication
CNC machining
Precision CNC turning and milling. Prototypes, spare parts and production runs from our own machining facility.
What we do
- CNC turning, from simple parts to complex geometries
- CNC milling in 3 and 4 axes
- Prototypes and production runs
- Machining of steel and non-ferrous metals
- CNC programming
- Dimensional and quality inspection of finished parts
Our CNC machining facility in Wrocław
We work at our machining facility in Wrocław, running CNC lathes and mills. We make precision parts both for our own projects and to customer order. The facility covers CNC turning up to 800 mm diameter and 3, 4 and 5-axis milling for more complex geometries.
Most of what leaves here is not a production run. It is one part, or five, that somebody needs because a machine is standing — a shaft, a bush, a gear, a housing that is no longer supplied. That shapes how we work: quick quotes, short lead times, and a willingness to take a single piece.
Working without a drawing
You do not need a drawing. Three routes work:
From the worn original. We measure it and machine a new one. Where the part is worn, we work back to what the dimension should have been rather than copying the wear.
From a 3D scan. For complex geometry — castings, cams, impellers — we scan the part and rebuild the model from the scan data.
From a sketch and a conversation. For simple parts, what the part has to fit and what it has to do is often enough.
Where the original design had a weakness, this is the moment to say so. A shaft that failed at a sharp change of section will fail again if we copy the sharp change of section. We will tell you what we would alter and why, and you decide.
Materials and inspection
We machine steels, stainless steels, non-ferrous metals and plastics. Material choice matters more on a replacement part than people expect — the original may have been chosen for a production process rather than for service life, and a one-off part is not bound by that.
Every part gets dimensional inspection before it ships. On a spare that has to fit a bearing or mate with an existing assembly, that check is the difference between a part that goes in and a machine that stays down another week.
Where this fits
CNC work backs everything else we do: cylinder reconditioning, machine component reconditioning and custom cylinder manufacture. That is why we can take on a reconditioning job where a part has to be remade — the capability is in the same building.
Why choose SOWMAR?
Our own facility
CNC lathes and mills, so a job is not queued behind somebody else's subcontract schedule.
From prototype to run
A single part and a production batch go through the same process, so the second matches the first.
Measured before it ships
Dimensional and quality inspection on every part, with the results recorded.
Related services
Welding and machine enclosures
Brackets, guards, platforms and machine enclosures, welded as part of servicing and installation work. We do n…
3D design and FEA
We design machines, dies, welding and soldering tooling and spare parts. FEA calculations and fatigue assessme…
3D scanning of parts and machines
We scan parts with no documentation, machines for installation design, and components to be reproduced. A scan…
Sending parts to us from abroad
We are based near Wrocław in south-west Poland, inside the EU. Parts arrive here by courier or pallet freight from across Poland and from EU countries — there is no customs clearance on shipments sent within the EU, so a pallet from Germany or Czechia moves the same way a domestic one does.
1
Send photos first, not the part
A photo of the nameplate, a photo of the whole unit and a line about what it does wrong. We will tell you whether it is worth reconditioning before you pay for freight.
2
Drain the oil
Hydraulic units must be drained before dispatch — couriers refuse them otherwise, and a leaking pallet is usually rejected on arrival.
3
Pallet, not a parcel
Anything above roughly 30 kg or 1.5 m travels safest strapped to a pallet, with the rod end protected. Long cylinders need the rod retracted and secured.
4
Send it to the workshop address
ul. Stalowa 1-13, hala 17, 55-330 Błonie, Poland. Put your company name and a contact number on the paperwork so we can match the pallet to the enquiry.
We can quote and invoice in EUR. If you are a VAT-registered business in another EU country, tell us your VAT number when you ask for the quote. Return freight is arranged the same way the part came in — we will confirm the cost together with the quotation, before any work starts.