Services · Servicing & maintenance
Hydraulic press servicing and overhaul
We repair hydraulic presses from the end they usually fail: the cylinder, the power pack and the controls. Either in our workshop or in your hall.
What we do
- On-site diagnosis of the press at your plant
- Press cylinder reconditioning with a pressure test
- Repair and inspection of the hydraulic power pack
- Replacement of hoses, valves and the sealing set
- Repair and replacement of controls and electrics
- Guarding, light curtains and bringing the press up to CE requirements
How a press failure usually starts
The press will not reach full force
Most often worn seals inside the cylinder — the oil leaks internally instead of doing work. The second direction to look is the relief valve and the pressure at the power pack.
The stroke is slower than it was
A drop in pump output, or air in the circuit. You normally see it in cycle time before you see it in the part.
Oil under the machine
A leak at the piston rod or under the gland. Leaving it turns a seal change into rod machining.
The ram creeps down under its own weight
Internal leakage or a failed check valve. That is a safety matter, not just an output one.
What an overhaul looks like here
Inspection and measurement
We check pressure, oil condition, the rod and the guides. We tell you what is cause and what is effect before anything is stripped.
A quotation split into options
Essential scope and recommended scope, separately. How much gets done now is your decision, and it is not taken midway through the job.
Reconditioning the assemblies
Cylinder, power pack, valves. Rods are ground and hard chrome plated; seats and guides are rebuilt on our own machine tools.
Assembly and pressure test
The press goes back with a test report, not with an assurance that it works.
A press is a hydraulic circuit inside a frame
Most press failures are not failures of the press. They are failures of the circuit that drives it. The cylinder, the power pack, the valves and the oil decide the force, the speed of the stroke and whether the ram holds position. The frame and the guides wear incomparably more slowly — which is why a press that has “got old” usually needs its drive overhauled, not the machine replaced.
That has a practical consequence at quotation time. A new press costs tens of thousands and arrives in months. An overhaul touches assemblies that can be rebuilt, so it costs a fraction of that and normally closes inside a few working days to a couple of weeks, depending on scope.
What we do to a press
We recondition the press cylinder — the most common reason for lost force. A new sealing set, rod grinding and hard chrome plating, cylinder bore rebuilt, and a pressure test with a report at the end.
We service the hydraulic power pack: pump, valves, filters, cooling and oil. A new cylinder dropped into a dirty circuit wears out exactly as fast as the old one, so we check oil and filters every time, even when the job was booked for something else.
We repair controls and electrics — from swapping failed components through to prefabricating a new control cabinet where the old one is past saving. We also make guarding and safety devices and bring the press up to requirements, documentation included.
On site or in our workshop
Presses rarely move without being dismantled, so by default we come to you. On site we handle diagnosis, hose and valve changes, power pack work, electrics and guarding.
What normally travels to the workshop is the cylinder alone — rod grinding and bore honing need machine tools that cannot be brought into your hall. For longer overhauls we agree in advance how many days the press will be down, so it can be planned into the production schedule.
When an overhaul is not the answer
A cracked frame, a bed permanently deformed by overload, or guides worn far enough that the ram no longer lands repeatably — with damage like that an overhaul is both more expensive and less certain than buying a machine. We say so before we start pricing, because losing the job beats invoicing for work that does not solve the problem.
The same applies to presses so old that every further assembly means parts made one at a time. At that point it is worth comparing the sum of those overhauls across two or three years against a sound second-hand machine.
Where to start
A photo of the press nameplate, a short description of the symptom, and whether the machine is stopped or still running. From that we will tell you whether it looks like a single visit or an overhaul with the cylinder removed, and give you a range and a date.
Why choose SOWMAR?
Overhaul instead of a new press
The frame and body are the slowest things on a press to wear out. If they are sound, an overhaul usually costs a fraction of a new machine.
One contractor for all of it
Hydraulics, electrics, controls and mechanics from one supplier — no responsibility passed between subcontractors.
We come to you
Presses are rarely movable. Diagnosis and most of the work happen on your floor.
A compliant press afterwards
While the press is open we bring it up to safety requirements and fill the gaps in its documentation.
Related services
Industrial machine servicing
Servicing of production machinery: fault diagnosis, breakdown repairs and scheduled inspections. We come to yo…
Maintenance support
Standing care of your machine fleet: inspections, critical spares to hand and a response to breakdowns without…
3D design and FEA
We design machines, dies, welding and soldering tooling and spare parts. FEA calculations and fatigue assessme…
Before you call
The three questions customers ask most often — answered before we raise an invoice.