Services · Component reconditioning
Vacuum pump reconditioning
Falling output, noise, or trouble holding vacuum? We find the cause, restore the worn components and bring the pump back to its working parameters.
What we do
- Diagnosis and identification of the cause
- Assessment of the pump's condition
- Restoration of worn components
- Repair of the lubrication system
- Verification of vacuum parameters
- Servicing and scheduled inspections
Our specialisations
Automotive
Pumps running continuously on production lines, where duty cycle rather than age decides wear.
Chemical industry
Installations where the vacuum parameters are part of the process specification.
Food industry
Equipment that has to be tight and repeatable, packaging lines above all.
General manufacturing
Vacuum technology in everyday plant operation — handling, forming and drying.
Reconditioning vacuum pumps
A vacuum pump holds the working parameters a process depends on, so its condition shows up directly in output, in safety and in running costs. Components wear with intensive duty, and that does not automatically mean a new pump: in most cases reconditioning restores full technical performance.
We carry out the diagnosis, the repair and the restoration of worn components on pumps used across industry. We assess the condition, identify what caused the failure and choose the fix to suit the way the installation actually runs — which is what stops the same fault returning.
Recognising wear before it becomes a failure
The useful signals arrive well before the pump stops.
The ultimate vacuum is worse than it was. The process takes longer to reach its set point, or never quite reaches it. Usually worn vanes or seals, sometimes oil that has been contaminated by the process.
The pump is louder, or the note changed. Bearings, or a vane no longer moving freely in its slot. This is the cheapest stage at which to act.
Oil condition and consumption. Darkened oil, or oil that needs topping up more often, points to process gas getting into the lubrication and to seals that are letting go.
Longer pump-down times. Often the earliest sign of all, and the easiest to miss, because operators adapt to it gradually rather than reporting it.
What we do
We strip and measure the pump, restore the worn components — vanes, seals, bearing seats, working surfaces — and repair the lubrication system, which is frequently the actual cause rather than a casualty. Then we verify the vacuum parameters before the pump goes back.
If the pump is part of a process where the vacuum level is specified, tell us the figure it has to hold. We will test against that rather than against a general standard, and put the result in writing.
Why choose SOWMAR?
Cheaper than a new pump
Especially on specialist process installations where a replacement is a long order.
Without a long stoppage
Fast diagnosis limits the risk of production standing still.
The cause, not the symptom
We repair what caused the failure, not only what it damaged.
Support afterwards
Scheduled inspections that keep the installation working.
Related services
Reconditioning of industrial and mechanical components
Reconditioning of shafts, gearboxes, spindles, motors, conveyors, hydraulic cylinders and pumps. Restored to s…
Diaphragm pump reconditioning
Reconditioning of diaphragm pumps: we diagnose the cause, replace diaphragms, seals and valves, then test tigh…
3D design and FEA
We design machines, dies, welding and soldering tooling and spare parts. FEA calculations and fatigue assessme…
Sending parts to us from abroad
We are based near Wrocław in south-west Poland, inside the EU. Parts arrive here by courier or pallet freight from across Poland and from EU countries — there is no customs clearance on shipments sent within the EU, so a pallet from Germany or Czechia moves the same way a domestic one does.
1
Send photos first, not the part
A photo of the nameplate, a photo of the whole unit and a line about what it does wrong. We will tell you whether it is worth reconditioning before you pay for freight.
2
Drain the oil
Hydraulic units must be drained before dispatch — couriers refuse them otherwise, and a leaking pallet is usually rejected on arrival.
3
Pallet, not a parcel
Anything above roughly 30 kg or 1.5 m travels safest strapped to a pallet, with the rod end protected. Long cylinders need the rod retracted and secured.
4
Send it to the workshop address
ul. Stalowa 1-13, hala 17, 55-330 Błonie, Poland. Put your company name and a contact number on the paperwork so we can match the pallet to the enquiry.
We can quote and invoice in EUR. If you are a VAT-registered business in another EU country, tell us your VAT number when you ask for the quote. Return freight is arranged the same way the part came in — we will confirm the cost together with the quotation, before any work starts.