Skip to content

Services · Cylinder reconditioning

Hydraulic cylinder reconditioning

We recondition hydraulic and pneumatic cylinders. Having our own machining facility means we can also build a cylinder from scratch when reconditioning is not worth it.

What we do

  • Our own CNC machining facility
  • New cylinders built where reconditioning is not worthwhile
  • Hard chrome plating of piston rods
  • Calibration of safety valves
  • Full end-of-job testing
  • Technical documentation
Worn hydraulic cylinders received for reconditioning
Worn hydraulic cylinders received for reconditioning

Our specialisations

Single-acting cylinders

Reconditioning of plunger cylinders with full technical diagnosis. Presses, lifts and clamping mechanisms.

Double-acting cylinders

Full reconditioning including hard chrome plating. Production machinery, construction plant and automation.

Telescopic cylinders

Multi-stage units — tippers, cranes and lifting platforms.

Cylinders with safety valves

Reconditioning with valve calibration and documentation of the settings.

How a reconditioning job runs

1

Inspection and quotation

We take the cylinder in, strip it and check the rod, the barrel, the guides and the sealing set. On that basis you get a price and an honest answer on whether it is worth doing.

2

Stripping and measurement

We measure the geometry against the documentation or against a reference. We establish what can be rebuilt and what has to be made new.

3

Machining and chrome plating

Rods are ground and hard chrome plated, restoring both the dimension and the surface finish. Missing parts are made on our own CNC equipment.

4

New sealing set

A complete set of new seals chosen for the working pressure, the temperature and the fluid the circuit actually runs on.

5

Assembly and pressure testing

We rebuild the cylinder and test it under pressure — tightness, smooth travel, and safety valve operation where fitted.

6

Documentation and handover

You get the test results and the scope of work in writing. The cylinder goes back ready to fit.

What we recondition

Piston rods

Straightening, grinding and hard chrome plating. We restore the nominal dimension and the surface finish the seal life depends on.

Barrels and bores

Honing and seat repair. We remove the scoring and ovality caused by wear or by contamination in the oil.

Sealing system

Complete replacement of seals and guide rings, chosen for the real operating conditions rather than the catalogue default.

Safety valves

Reconditioning and calibration, with documentation confirming the settings.

Mountings

Repairs to eyes, pins and mounting bushes — the most commonly skipped item, and the one that decides whether the cylinder sits right in the machine.

Parts no longer available

Where the original part is discontinued or the maker has dropped support, we make it new from measurements or a drawing.

When to recondition and when to buy new

Reconditioning makes sense

The body and barrel are sound and it is the rod and seals that have worn. That is the common case — you get the cylinder back for a fraction of a new one.

A new cylinder is the better call

The barrel is cracked or permanently deformed. We say so at the quotation stage rather than rebuilding something that cannot honestly be restored.

Reconditioning on our own machining facility

We recondition hydraulic and pneumatic cylinders for customers in Wrocław, Lower Silesia, across Poland and — by pallet freight — from other EU countries. Reconditioning is the economic alternative to buying new: you keep a working cylinder for a fraction of the price of a replacement.

We have the workshop and the people to rebuild difficult units, and because we can also manufacture, we are not forced to recommend reconditioning when it is the wrong answer. We work with CNC lathes, milling machines and hydraulic presses, we have a hard chrome plating bay, and we have complete pressure testing equipment.

We recondition all cylinder types: single-acting (plunger), double-acting, telescopic and units with integrated safety valves. We handle cylinders from Bosch Rexroth, Parker, Hyva, Binotto, Edbro, Brevini, Hydromatik and many others. Rod diameters from 16 mm to 500 mm, working pressures to 400 bar.

Every job starts with a detailed technical inspection: geometric tolerances measured, working surfaces assessed, and the cause of the failure identified — because a cylinder that failed for a reason will fail again if the reason stays. From that we set the scope: machining, hard chrome plating of the rod, bore honing, a complete new sealing set, and final pressure testing. The work is covered by a warranty.

Why choose SOWMAR?

Cost

Reconditioning typically costs a fraction of what a comparable new cylinder does.

Turnaround

Quick diagnosis and short lead times, because the machining and the plating are both in house.

Warranty

All reconditioned components are covered by a warranty.

Experience

Eight years reconditioning industrial components, not only cylinders.

Sending parts to us from abroad

We are based near Wrocław in south-west Poland, inside the EU. Parts arrive here by courier or pallet freight from across Poland and from EU countries — there is no customs clearance on shipments sent within the EU, so a pallet from Germany or Czechia moves the same way a domestic one does.

1

Send photos first, not the part

A photo of the nameplate, a photo of the whole unit and a line about what it does wrong. We will tell you whether it is worth reconditioning before you pay for freight.

2

Drain the oil

Hydraulic units must be drained before dispatch — couriers refuse them otherwise, and a leaking pallet is usually rejected on arrival.

3

Pallet, not a parcel

Anything above roughly 30 kg or 1.5 m travels safest strapped to a pallet, with the rod end protected. Long cylinders need the rod retracted and secured.

4

Send it to the workshop address

ul. Stalowa 1-13, hala 17, 55-330 Błonie, Poland. Put your company name and a contact number on the paperwork so we can match the pallet to the enquiry.

We can quote and invoice in EUR. If you are a VAT-registered business in another EU country, tell us your VAT number when you ask for the quote. Return freight is arranged the same way the part came in — we will confirm the cost together with the quotation, before any work starts.