Services · Cylinder reconditioning
Liebherr cylinder reconditioning
We recondition boom, stick and bucket cylinders — long rods and large diameters, where straightness matters as much as sealing.
Cylinder reconditioning
Reconditioning of cylinders for Liebherr machines: boom, stick and bucket. Chrome plating of long rods, large diameters, collection from site. Wrocław, Poland.
Our specialisations
Boom and stick cylinders
Long stroke at large diameter. Beyond sealing, rod straightness decides everything — a bent rod destroys the guiding within tens of working hours.
Bucket and attachment cylinders
These work in the worst of the dust and most often have damaged wipers, which is the real cause of leaks that keep coming back.
Outriggers and stabilisers
Components that hold a load stationary. Here the valve condition and internal tightness decide, not how the rod looks.
Dust and moisture
Corrosion while the machine stands, and grit dragged in on retraction, destroy chrome faster than working hours do.
Earthmoving cylinders fail differently
An industrial cylinder in a clean hall wears evenly and slowly. A cylinder on a machine working outdoors does not. Three things dominate, and none of them is the sealing set.
Rod straightness. Boom and stick cylinders are long and take side loads they were never meant to take, usually the moment somebody uses the boom to shove something. A rod with even slight runout wears its guide bush unevenly, and once the guiding has gone the seal follows within tens of working hours. So we measure runout before quoting, and straighten where it is worth straightening.
Damaged wipers. The bucket cylinder lives in the dust. Its wiper takes the grit, and once the wiper is split the grit goes straight past it into the seal and onto the rod. This is the single most common reason a cylinder that was “just rebuilt” is leaking again six weeks later. Wipers get replaced every time here, regardless of what the enquiry asked for.
Corrosion while parked. A machine that sits outside for a fortnight with the rods extended comes back with pitting on the exposed chrome. Each pit is a small knife that cuts the seal on every stroke. Where the pitting is shallow the chrome can be rebuilt; where it is deep the rod gets ground undersize first and then re-plated to dimension.
Outriggers are a safety item
Stabiliser and outrigger cylinders hold a load stationary, which puts them in a different category from the rest of the machine. What decides whether they are safe is internal tightness and the condition of the load-holding valve, not how the rod looks from the outside.
We test those under load rather than just for leakage, and the result goes in the report. If a valve cannot be reconditioned to hold reliably, we say so instead of reassembling around it.
Large diameters and long rods
The practical constraint on this work is capacity: long rods need the length to grind and the bath to plate. Both are here, so a boom cylinder does not get shipped to a third party and back with two weeks added to the lead time.
Cylinders can be collected from your yard. That matters more than it sounds — a machine with the boom cylinder removed is not going anywhere, so the faster the unit is on a truck, the shorter the whole stoppage is.
An independent workshop, not an authorised service centre
We are an independent reconditioning workshop based near Wrocław, Poland. We are not an authorised service centre for this manufacturer and we do not act on their behalf — brand names appear here only to say what equipment we work on. In practice that usually means a shorter lead time and a lower cost, and on discontinued series it is often the only route other than buying a new cylinder.
Why choose SOWMAR?
Long rods handled here
Grinding and chrome plating of long, large-diameter rods is done in our own bay rather than subcontracted.
Straightness measured
Rods are checked for runout and straightened where needed — skipping this is why some rebuilds fail within weeks.
Wipers replaced as standard
A damaged wiper is the usual reason a leak returns. It costs little and gets changed every time.
Collection from site
Cylinders can be collected from the yard, which matters when the machine cannot be moved.
Related services
Bosch Rexroth cylinder reconditioning
Reconditioning of Bosch Rexroth hydraulic cylinders: end cushioning, stroke measurement, rod chrome plating an…
Cylinders with safety valves
We build and service hydraulic cylinders fitted with safety valves. Valve calibration, pressure testing and do…
Double-acting cylinder reconditioning
Reconditioning of double-acting hydraulic cylinders: diagnosis, seals, rods, honing and pressure testing. Hard…
Before you call
The three questions customers ask most often — answered before we raise an invoice.
Sending parts to us from abroad
We are based near Wrocław in south-west Poland, inside the EU. Parts arrive here by courier or pallet freight from across Poland and from EU countries — there is no customs clearance on shipments sent within the EU, so a pallet from Germany or Czechia moves the same way a domestic one does.
1
Send photos first, not the part
A photo of the nameplate, a photo of the whole unit and a line about what it does wrong. We will tell you whether it is worth reconditioning before you pay for freight.
2
Drain the oil
Hydraulic units must be drained before dispatch — couriers refuse them otherwise, and a leaking pallet is usually rejected on arrival.
3
Pallet, not a parcel
Anything above roughly 30 kg or 1.5 m travels safest strapped to a pallet, with the rod end protected. Long cylinders need the rod retracted and secured.
4
Send it to the workshop address
ul. Stalowa 1-13, hala 17, 55-330 Błonie, Poland. Put your company name and a contact number on the paperwork so we can match the pallet to the enquiry.
We can quote and invoice in EUR. If you are a VAT-registered business in another EU country, tell us your VAT number when you ask for the quote. Return freight is arranged the same way the part came in — we will confirm the cost together with the quotation, before any work starts.