Services · Cylinder reconditioning
Bosch Rexroth cylinder reconditioning
We recondition Bosch Rexroth cylinders including versions with end cushioning and integrated stroke measurement, where the geometry matters as much as the seal.
Cylinder reconditioning
Reconditioning of Bosch Rexroth hydraulic cylinders: end cushioning, stroke measurement, rod chrome plating and remade parts. Independent workshop in Poland.
Our specialisations
End cushioning
Cushioning bushes and throttles decide how the cylinder decelerates at the end of stroke. Worn cushioning shows as knocking, not as a leak.
Integrated stroke measurement
On units with a position transducer we hold the sensor bore geometry, so the machine's control loop does not need retuning.
Heavy industrial builds
Presses and forming machinery — high forces, high cycle counts, and bores that need honing rather than just a seal change.
Discontinued series
Where the seal kit is no longer catalogued, seals are selected from measured dimensions and metal parts are remade here.
What is specific about these cylinders
Two features turn up often enough on this manufacturer’s industrial cylinders to shape how the job runs: end cushioning and integrated stroke measurement. Both are easy to get wrong in a rebuild, and both are expensive to get wrong.
End cushioning decelerates the piston over the last stretch of travel, so the cylinder does not hammer its own end caps. It works through a cushioning bush entering a matching recess, with an adjustable throttle to set the rate. When the bush wears, the cylinder starts knocking at the end of stroke — and because it does not leak, the symptom is regularly blamed on mounting play instead. We measure the bush and its seat as a matter of course.
Integrated stroke measurement means a transducer sits inside the rod or the head. Here the tightness of the cylinder is only half the job: if the measuring seat is machined to a different dimension, the machine’s control loop has to be retuned after refitting. That usually costs more than the reconditioning did, so we hold that geometry.
The ordinary wear
Beyond those two, the pattern is the one common to industrial cylinders. Seals harden and lose their sealing edge. The bore picks up scoring from contamination in the oil, which then destroys each new seal set faster than the last. The rod loses chrome in patches, and each patch becomes a site for corrosion and a knife edge for the rod seal.
This is why we measure before quoting rather than after. A cylinder that needs a seal kit and a cylinder that needs the bore honed and the rod re-chromed look identical from the outside, and the difference between them is most of the price.
Presses and forming machinery
Most of these units reach us from presses and forming machines — high forces and high cycle counts. Two things follow.
First, the failure is rarely only in the cylinder. A press that has lost force usually has something happening at the power pack or the relief valve as well, and refitting a perfect cylinder into that circuit buys a few months. If you tell us what machine it came off, we will say what else is worth checking while it is out.
Second, downtime is the real cost. Tell us when the machine is scheduled to stop and we will work to that, rather than quoting a lead time that ignores your production plan.
An independent workshop, not an authorised service centre
We are an independent reconditioning workshop based near Wrocław, Poland. We are not an authorised service centre for this manufacturer and we do not act on their behalf — brand names appear here only to say what equipment we work on. In practice that usually means a shorter lead time and a lower cost, and on discontinued series it is often the only route other than buying a new cylinder.
Why choose SOWMAR?
Cushioning rebuilt, not ignored
Cushioning bushes and throttle screws are checked and restored — the part most workshops leave alone because it does not leak.
Sensor geometry preserved
No re-calibration of the machine after refitting, because the measuring seat comes back to its original dimension.
Chrome plating in house
The rod does not travel to a subcontractor, which removes both a delay and a transit risk.
Test documentation
A pressure test report goes back with every cylinder.
Related services
Cylinders with safety valves
We build and service hydraulic cylinders fitted with safety valves. Valve calibration, pressure testing and do…
Double-acting cylinder reconditioning
Reconditioning of double-acting hydraulic cylinders: diagnosis, seals, rods, honing and pressure testing. Hard…
Fletcher cylinder reconditioning
Reconditioning of cylinders for Fletcher mining machinery: roof supports, lifting and extension rams. No waiti…
Before you call
The three questions customers ask most often — answered before we raise an invoice.
A hydraulic cylinder losing force — five common causes
The machine runs slower than it used to, the cylinder will not reach the end of stroke, or it creeps down under load
ReadReconditioning or a new cylinder — how to work out which pays
The cylinder can be repaired, but it is not clear whether reconditioning or buying new works out cheaper
ReadSending parts to us from abroad
We are based near Wrocław in south-west Poland, inside the EU. Parts arrive here by courier or pallet freight from across Poland and from EU countries — there is no customs clearance on shipments sent within the EU, so a pallet from Germany or Czechia moves the same way a domestic one does.
1
Send photos first, not the part
A photo of the nameplate, a photo of the whole unit and a line about what it does wrong. We will tell you whether it is worth reconditioning before you pay for freight.
2
Drain the oil
Hydraulic units must be drained before dispatch — couriers refuse them otherwise, and a leaking pallet is usually rejected on arrival.
3
Pallet, not a parcel
Anything above roughly 30 kg or 1.5 m travels safest strapped to a pallet, with the rod end protected. Long cylinders need the rod retracted and secured.
4
Send it to the workshop address
ul. Stalowa 1-13, hala 17, 55-330 Błonie, Poland. Put your company name and a contact number on the paperwork so we can match the pallet to the enquiry.
We can quote and invoice in EUR. If you are a VAT-registered business in another EU country, tell us your VAT number when you ask for the quote. Return freight is arranged the same way the part came in — we will confirm the cost together with the quotation, before any work starts.