Guides · 29 September 2026
How to measure a cylinder and get a quote without sending it in
The cylinder is still fitted in the machine and you need to know the cost of repair before deciding to take it out
The six dimensions to send
Rod diameter
Measured with callipers on a clean, undamaged section. This is the dimension that decides the seals, so send it first.
Bore diameter
The outside diameter of the tube and, if you know it, the inside diameter. Together with pressure they give the force the cylinder develops.
Stroke
The difference in length between extended and retracted. If it cannot be extended in the machine, say so rather than estimating.
Installed length
The distance between mounting centres with the cylinder retracted. This is the dimension that decides whether it fits the machine.
Mounting type
Eye, clevis, spherical bearing, foot, trunnion. Give the hole diameter and the width across the mounting as well.
Hydraulic ports
Thread type and size, and where they sit — on the side, on the end, same side or opposite sides.
What else to include
A photograph of the whole cylinder
Shows the type of construction, the mounting arrangement and the general condition better than any description.
The rod photographed in raking light
Side light reveals scores, pitting and dull patches that a straight-on photograph hides in the reflection.
The nameplate, if there is one
The maker's designation and type sometimes give the catalogue dimensions straight away.
Working pressure
From the machine documentation or from a gauge. It affects the choice of seals and materials.
A description of the symptom
Leaking, creeping under load, simply slower — it points at the likely scope before any diagnosis.
The date you need
If the machine is stopped, say so at once. It changes how the work is planned in the workshop.
Why measure before sending anything
The most common situation in maintenance runs like this: the cylinder is leaking, the machine is still running, and the decision to stop it depends on what the repair will cost and how long it takes. To know that, somebody has to look at the cylinder — and to look at it, it has to come out. The loop closes, and the matter waits for a breakdown.
There is a way out: a full set of dimensions and two photographs are enough to estimate the scope and give an order of magnitude before anything is removed. It does not replace diagnosis, but it is enough to decide whether and when to plan the stoppage.
The sequence, which takes a quarter of an hour
Start with preparation: the cylinder should be unloaded and cold, and the rod wiped dry. Take the measurements with the cylinder retracted, because that is how installed length is defined — the dimension that decides whether it fits the machine.
Measure the rod diameter with callipers on a section free of damage; on a score or a pit the reading will be low. Give the bore at least as an outside diameter; if you know the inside diameter from documentation, better still, because that and the pressure define the force. Work out the stroke as the difference between extended and retracted length. If it cannot be extended in the machine, say so plainly rather than quoting a figure from memory.
That leaves mountings and ports. For the mounting, the type matters, plus the hole diameter and the width across it. For the ports, the thread type and size and where they sit on the body. These are the details that most often decide whether the unit goes back without modifications.
Photographs say what words cannot
Two photographs improve a quote more than any further dimension. The first is the whole cylinder with the mountings visible — it shows the construction and how it is installed. The second is the rod along its whole length in raking light. Light at an angle reveals scores, dull patches and traces of corrosion that a straight-on photograph loses in the reflection.
If there is a legible nameplate on the body, photograph that too. Sometimes it gives the catalogue dimensions immediately and shortens the whole procedure to one picture.
What else speeds up the answer
Besides dimensions and photographs, three pieces of information count. The working pressure, because it affects the choice of seals and materials. A description of the symptom — leaking externally, creeping under load, or simply weak — because it points at the likely scope. And the timing: a stopped machine is an entirely different mode of work in the workshop from a repair planned in advance.
Machine documentation is not needed. We also work on cylinders for which no catalogue and no parts exist any more — the missing components are made here, with the dimensions taken from the dismantled unit.
What you get back
From a set like that we can say whether this looks like a routine seal change or a full reconditioning with rod grinding and chrome plating, and what the realistic lead time is. We can also assess the alternative straight away: whether in this particular case building a new cylinder makes more sense.
The binding quotation comes only after diagnosis, because only stripping the unit shows the state of the bore and the real extent of the wear. But for planning a stoppage and agreeing a budget, the initial answer is usually entirely sufficient — and it costs a quarter of an hour at the machine.
Częste pytania
Is an initial quote from dimensions binding?
An initial quote shows the order of magnitude and the scope that is in play; the binding one comes after diagnosis. Only stripping the cylinder shows the condition of the bore and the rod, which is what decides the scope of work.
What if the cylinder cannot be extended in the machine?
Give the installed length with the cylinder retracted and note that the stroke is unknown. It can be established from the construction and the dimensions once it is stripped; what matters is not presenting an estimate as a certainty.
Do you need the machine documentation?
No. We also work on cylinders with no documentation and no catalogue parts available, rebuilding the dimensions from the unit itself once it has been dismantled.
Can you make a new cylinder from the same dimensions?
Yes. We have our own machining facility and build cylinders to order where reconditioning is not worthwhile or the original is unavailable. The set of dimensions needed to quote is the same in both cases.
Related guides
A hydraulic cylinder losing force — five common causes
The machine runs slower than it used to, the cylinder will not reach the end of stroke, or it creeps down under load
Reconditioning or a new cylinder — how to work out which pays
The cylinder can be repaired, but it is not clear whether reconditioning or buying new works out cheaper