Services · Cylinder reconditioning
Parker cylinder reconditioning
We recondition Parker cylinders to catalogue dimensions — including the ones the manufacturer no longer supplies repair kits for.
Cylinder reconditioning
Reconditioning of Parker hydraulic cylinders: seals, rod chrome plating and parts remade for discontinued series. Independent workshop near Wrocław, Poland.
Our specialisations
ISO standard cylinders
Series built to ISO 6020 and 6022 have repeatable mounting dimensions, so parts can be remade faster than on non-standard designs.
Industrial and mobile versions
Presses, automation and production machinery, or vehicle-mounted units — different conditions mean a different seal specification.
Cylinders with position sensors
On units with stroke measurement we preserve the sensor seat geometry, so the machine controls do not need re-calibrating.
Discontinued series
No repair kit in the catalogue does not end the conversation — missing components are made in our own workshop.
What we do to a Parker cylinder
Read the code off the nameplate
The code on the body gives the series, the diameters, the stroke and the port arrangement. It is the fastest route to the dimensions without measuring everything.
Strip and measure the wear
We check the bore, the rod surface and the guiding. Only measurement settles whether a seal kit alone will do.
Rebuild the working surfaces
Grinding and hard chrome plating of the rod, and machining the bore back to a dimension the seal can work against.
Match seals to the conditions
Temperature, oil type and duty cycle decide the material more than the diameter does.
Assemble and pressure test
A tightness and function test at working pressure, with the report handed over along with the cylinder.
Why Parker cylinders recondition differently from one-off designs
A large share of this manufacturer’s cylinders are built to ISO 6020 and 6022, which is to say in standardised dimensions. For a workshop that is a concrete advantage: diameters, strokes and mounting dimensions are predictable, and mating parts can be remade without reverse-measuring the whole machine. So the repair starts by reading the code off the nameplate, not by measuring everything.
That same code settles something that gets missed when people shop for a substitute: the port arrangement and the mounting style. Two cylinders with identical bore and stroke can differ in where the ports sit, and that decides whether the unit goes back without altering the pipework.
What wears out
In industrial installations — presses, production machinery, automation — it is the sealing system that goes. The cylinder works indoors, in clean surroundings, at a steady temperature, so the surfaces degrade slowly and evenly. Reconditioning is then routine: strip, measure, new seal set, reassemble.
Vehicle-mounted and outdoor units are a different matter. There you get rod corrosion while the machine stands, contamination dragged in on retraction, and mechanical damage to the surface. A seal replaced without rebuilding the chrome will be gone in weeks — which is why on those units the assessment of the rod matters more than the strip-down itself.
Units with position sensors are their own category. Tightness is not the only thing that counts; the geometry of the sensor seat has to be preserved. Change that dimension and the machine controls need re-calibrating, which usually costs more than the repair.
When a missing repair kit stops being an obstacle
The most common reason a structurally sound cylinder gets scrapped is “there is no repair kit any more”. On discontinued series that is normal and settles nothing by itself.
Seals are selected from installation dimensions, not from a part number — and with the cylinder stripped, we have every dimension. Metal parts that cannot be bought we make on site: guide bushes, glands, pistons, rods. With the body in good condition, rebuilding the rest is workshop work rather than a parts hunt.
The line is drawn where the body itself is damaged. A cracked barrel, a permanently deformed tube or a torn-out mounting are the cases where it is more honest to say the repair makes no economic sense — and then we offer to build a new cylinder rather than an expensive repair with a short life.
What we need to quote
The quickest route is a photo of the nameplate; the code carries most of what we need. If the plate is unreadable, six dimensions will do: rod diameter, bore diameter, stroke, installed length, mounting type, and the type and position of the ports. Plus two photos: the whole unit, and the rod in raking light — side light shows scoring and pitting that a straight-on photo hides.
It also helps to know the working conditions: pressure, oil type, temperature, and whether the machine works indoors or outside. That decides the seal material, and therefore how long the repair actually lasts.
An independent workshop, not an authorised service centre
We are an independent reconditioning workshop based near Wrocław, Poland. We are not an authorised service centre for this manufacturer and we do not act on their behalf — brand names appear here only to say what equipment we work on. In practice that usually means a shorter lead time and a lower cost, and on discontinued series it is often the only route other than buying a new cylinder.
Why choose SOWMAR?
No waiting on a delivery
We work with what arrived at the workshop instead of waiting on a repair kit from abroad.
Dimensions unchanged
The cylinder goes back with its original stroke and ports, so fitting it needs no changes to the machine.
Non-standard builds too
Special versions and withdrawn series are rebuilt from the dismantled unit itself.
Test documentation
The pressure test report goes to the customer with the equipment.
Related services
Bosch Rexroth cylinder reconditioning
Reconditioning of Bosch Rexroth hydraulic cylinders: end cushioning, stroke measurement, rod chrome plating an…
Cylinders with safety valves
We build and service hydraulic cylinders fitted with safety valves. Valve calibration, pressure testing and do…
Double-acting cylinder reconditioning
Reconditioning of double-acting hydraulic cylinders: diagnosis, seals, rods, honing and pressure testing. Hard…
Before you call
The three questions customers ask most often — answered before we raise an invoice.
A hydraulic cylinder losing force — five common causes
The machine runs slower than it used to, the cylinder will not reach the end of stroke, or it creeps down under load
ReadReconditioning or a new cylinder — how to work out which pays
The cylinder can be repaired, but it is not clear whether reconditioning or buying new works out cheaper
ReadHow to measure a cylinder and get a quote without sending it in
The cylinder is still fitted in the machine and you need to know the cost of repair before deciding to take it out
ReadSending parts to us from abroad
We are based near Wrocław in south-west Poland, inside the EU. Parts arrive here by courier or pallet freight from across Poland and from EU countries — there is no customs clearance on shipments sent within the EU, so a pallet from Germany or Czechia moves the same way a domestic one does.
1
Send photos first, not the part
A photo of the nameplate, a photo of the whole unit and a line about what it does wrong. We will tell you whether it is worth reconditioning before you pay for freight.
2
Drain the oil
Hydraulic units must be drained before dispatch — couriers refuse them otherwise, and a leaking pallet is usually rejected on arrival.
3
Pallet, not a parcel
Anything above roughly 30 kg or 1.5 m travels safest strapped to a pallet, with the rod end protected. Long cylinders need the rod retracted and secured.
4
Send it to the workshop address
ul. Stalowa 1-13, hala 17, 55-330 Błonie, Poland. Put your company name and a contact number on the paperwork so we can match the pallet to the enquiry.
We can quote and invoice in EUR. If you are a VAT-registered business in another EU country, tell us your VAT number when you ask for the quote. Return freight is arranged the same way the part came in — we will confirm the cost together with the quotation, before any work starts.